SPI Products A-Z
- Enamo Grip
- Enamo Grip SAS Coating
- HPC™ Coating
- HSC™ Coating
- iSTUCCO™ System
- Lining Kote
- Mastic Sealing Tape
- Moist Metal Grip
- Omega Fire™
- Rust Grip®
- SP Liquid Membrane
- SP Super Cleaner
- Super Base
- Super Therm®
Enamo Grip is a tough, moisture curing, two-component polyurethane enamel, which produces a uniquely hard and durable coating film. It will demonstrate unsurpassed semi-gloss retention, color-retention, graffiti-resistance and chalk resistance when utilized for exterior coating situations. Enamo Grip will also provide outstanding resistance to water and humidity, stains, chemicals, and solvents, as well as exceptional scuff, mark, and impact-resistance.
Enamo Grip SAS Coating
Designed to be a watertight film while holding additives to make it slick and hard over the surface to resist the attachment of barnacles, seaweed and algae.
Epoxotherm is a ceramic-based, two-part epoxy that can be submerged and add insulation value to any substrate over which it is coated. It’s also designed to insulate wet surfaces. It combines the ceramics of Super Therm® for exceptional reflective and insulative performance, with the toughness and submersible capabilities of industrial grade epoxy.
Get "high" heat protection that surpasses conventional insulation with HPC™ Coating. HPC™ Coating is a ceramic based, water-borne insulating coating designed to insulate in high temperature situations. Use HPC™ Coating as a base coat/primer or build layers for additional protection.
Get heat protection/insulation that surpasses conventional insulation with HSC™ Coating, a ceramic based, water-borne insulating coating designed to insulate in medium temperature situations. Use HSC™ Coating as a base coat/primer or build layers for additional protection.
The iSTUCCO™ System creates an unbeatable and affordable solution to stop heat and/or cold conduction through the coating film and a beautiful, long-lasting stucco finish. It combines the best properties of two outstanding products, SP Ceramic Stucco and the top coat of Super Therm®, which is designed with four separate ceramics; two are reflective, one is an infrared blocker, and the fourth acts as a dead air space between the coated surface and the substrate. The result is an applied coating that is both reflective and insulating.
Protect against the harshest acids, bases, chemicals and solvents with Lining Kote UHS. Its two-part epoxy composition provides durable and flexible protection for your coatings.
Mastic Sealing Tape
Protect against water and leaks with Mastic Sealing Tape. Designed for use on seams of metal buildings, Mastic Sealing Tape bonds with coatings to completely seal the roofing structure. It works with Super Therm® and Enamo Grip to create a monolithic and long lasting roofing system, but must be overcoated initially with Super Base (HS) to seal the Tape.
Moist Metal Grip
Protect submerged surfaces with durable Moist Metal Grip. This two-part epoxy is designed to provide a water-resistant, anti-corrosion coating for wet or submerged surfaces as well as protect metal surfaces already experiencing moisture or condensation that cannot be stopped and dried.
ASTM E119 Fire Endurance Testing on Coated Steel I-Beam
The outside construction of furnace used in test is steel and is lined with a ceramic refractory insulation. A single burner is centered vertically in the wall opposite the sample. This burner is rated 1.5 million BTU/HR and is of the flat flame or non-impinging flame design. Furness conditions are monitored by three Inconel-sheathed chromel-alumel thermocouples. This thermocouples are positioned 6" from the face of the sample. A transition piece was placed on the front of the furnace where the sample was to be placed. The sample was placed through this opening so that the I-Beam is exposed to the inside of the furnace and support by the 1/2" plate.
The fire test was run following the ASTM E119 time-temperature curve.
The endpoint for this ASTM E119 Test occurs when all the thermocouples on the sample reach an average of 1,000 F.
Build extra safety into structures with Omega Fire™, a ceramic-loaded, water-borne fireproofing coating. Omega Fire™ stays intact above 2000 degrees F (1100 degrees C) and has a 2-3 hour fire rating. Using the combination of HPC and Omega Fire™, a 7-hour rating was achieved on a support beam inside the furnace at 2000 degrees F (1100 C).
Seal virtually any surface and protect it against corrosion, weather and physical wear with Rust Grip®, a three-coats-in-one system that acts as a primer, intermediate, and top coat with a single application.
SP Liquid Membrane
SP Liquid Membrane is a tough, one-part elastomeric hydrocarbon rubber coating that is loaded with a ceramic pigment for strength. Upon curing, it provides a protective coating film of superior adhesion and flexibility, and is resistant to abrasion and impact. It can be used as a primer, as a one-coating system or as a top coat to seal Super Therm® from ponding water.
SP Super Cleaner
SP Super Cleaner (Graffiti Cleaner) is a liquid cleaner for removing graffiti made from a blend of glycol esthers and other chemicals. It will remove most types of paint, including Krylon spray paints and magic markers. It’s environmentally friendly and easy to use.
Reduce energy costs for less with Sunshield, a ceramic-based, water-borne, insulating coating. Sunshield contains a similar ceramic package as our best-selling Super Therm®, but was designed primarily for areas that are facing radiational heat and no harsh environmental conditions.
See 5 STAR Reviews at Home Depot
Seal and cover surfaces with Super Base (HS), a high performance base coat and primer designed specifically for use with Super Therm® and Sunshield. Super Base (HS) is made with a combination of the highest-performances elastomeric acrylics to provide long-lasting protection.
Super Therm® is the most effective and longest lasting ceramic insulation coating on the market today (showing 10 year rechecking of roofing showing no drop in performance, even though they are dirty). It’s a ceramic-based (using 4 different ceramic compounds specifically selected to block radiation), water-borne insulating coating designed to block heat load, moisture penetration, and air infiltration over a surface – all while reducing important energy costs. Super Therm® reflects over 95% of the three radiation sources from the sun: ultraviolet, visual light and infrared rays.